Blickle wheel series info box
Tread and tyre hardness. Smooth operation and floor preservation.
To make it easier for you to choose the correct product, we provide a Blickle info box for each wheel series. This provides an overview of the tread and tyre hardness of a wheel, its smooth operation and floor preservation, rolling resistance and wear resistance.
Tread and tyre hardness is rated on a scale from very soft to very hard, while the other categories are rated from satisfactory to outstanding.
| Tread and tyre hardness | |
 |
65 Shore A |
| Smooth operation and floor preservation | |
 |
excellent |
| Rolling resistance | |
 |
very good |
| Wear resistance | |
 |
good |
Tread and tyre hardness
The tread & tyre hardness is indicated in the info box in images on the product pages. The further the marking is to the right, the harder the tread. Hardness for
- elastomers and polyurethanes is provided in Shore A,
- Shore D for solid plastics and
- using the Brinell scale for metals.
There is no linear correlation between the various hardness testing methods. The values in the graphic were determined empirically and are provided for reference purposes.
| Material | Tread and tyre hardness | ||
| Pneumatic tyre / soft rubber |  |
50-60 Shore A | |
| Elastic solid rubber | |
65 Shore A | |
| Super-elastic solid rubber | |
70 Shore A | |
| Standard solid rubber |  |
80 Shore A | |
| Thermoplastic polyurethane (TPU), soft | |
80 Shore A | |
| Thermoplastic rubber-elastomer (TPE) | |
85 Shore A | |
| Polyurethane 75 Shore A | |
75 Shore A | |
| Polyurethane 92 Shore A |  |
92 Shore A | |
| Thermoplastic polyurethane (TPU), hard | |
92–98 Shore A | |
| Polypropylene |  |
60 Shore D | |
| Nylon | |
70 Shore D | |
| Cast nylon | |
80 Shore D | |
| Cast iron / steel | |
180–230 HB |
Smooth operation and floor preservation
The higher the score in this category, the quieter the wheel is and the easier it is on surfaces.
Floor preservation
Hard treads put more strain on a floor than softer
treads. A tread with five points in the smooth
operation and floor preservation category has
exceptionally good floor preservation qualities.
Floor surface preservation is measured on the basis of average floor pressure. Reference values for each tread material are provided to the right.
Smooth operation
In principle, vehicles tend to be quieter when they
have large wheels with soft thick treads. Hard
treads result in higher levels of noise than soft
treads. A high score in the smooth operation and
floor preservation category would therefore lead to
expect low levels of vibration and noise emission
when transporting goods.
Hard wheels can also be used with low levels of noise and a high degree of operational comfort when transporting light loads on a soft surface (e.g. carpet).
Calculating average floor pressure
The average floor pressure is calculated by
dividing the radial force [N] by the wheel contact
surface [mm²].
| Material | Smooth operation / floor preservation | Average floor pressure | |
| Pneumatic tyre / soft rubber |  |
0,8 N/mm² | |
| Elastic solid rubber |  |
1,8 N/mm² | |
| Super-elastic solid rubber | |
1,5 N/mm² | |
| Standard solid rubber | |
3,5 N/mm² | |
| Thermoplastic polyurethane (TPU), soft | |
4,0 N/mm² | |
| Thermoplastic rubber-elastomer (TPE) |  |
4,5 N/mm² | |
| Polyurethane 75 Shore A | |
3,5 N/mm² | |
| Polyurethane 92 Shore A | |
8,0 N/mm² | |
| Thermoplastic polyurethane (TPU), hard | |
11,0 N/mm² | |
| Polypropylene / nylon |  |
40,0 N/mm² | |
| Cast nylon | |
60,0 N/mm² | |
| Cast iron / steel |  |
>350 N/mm² |
Starting, rolling and swivel resistance
Starting resistance reflects the amount of force required to get the wheel in motion when it is at a standstill. Rolling resistance refers to the amount of force required to keep the wheel moving in a uniform manner. Starting and rolling resistance are affected by the following factors:
- wheel diameter
- tread geometry
- tread & tyre hardness
- rebound resilience of the tread
- wheel bearing
- surface
Rolling resistance eoccurs as a result of the constant compression and decompression of the tread while the wheel is rolling (hysteresis).
Rolling resistance is measured using a test bench. Measurements are taken under ideal conditions:
- level, smooth, steel surface free of dirt and obstacles
- speed: 4 km/h
- temperature: +20 °C
- load: ⅔ of max. load capacity
These standardised conditions make it possible to compare the rolling resistances of different wheel series.
| Material | Rolling resistance | ||
| Pneumatic tyre / soft rubber | |
good | |
| Elastic solid rubber | |
very good | |
| Super-elastic solid rubber | |
good | |
| Standard solid rubber | |
satisfactory | |
| Thermoplastic polyurethane (TPU), soft | |
very good | |
| Thermoplastic rubber-elastomer (TPE) | |
very good | |
| Polyurethane 75 Shore A (Softhane®) | |
very good | |
| Polyurethane 75 Shore A (Besthane® Soft) | |
excellent | |
| Polyurethane 92 Shore A (Extrathane®) | |
very good | |
| Polyurethane 92 Shore A (Besthane®) | |
excellent | |
| Thermoplastic polyurethane (TPU), hard | |
very good | |
| Polypropylene / nylon | |
excellent | |
| Cast nylon | |
excellent | |
| Cast iron / steel | |
excellent |
Different application conditions (surface quality, temperature, speed, etc.) must be taken into consideration when designing the running gear and can have a significant impact on rolling resistance.
Swivel resistance is the resistance required to align swivel castors in the direction of travel.
Swivel resistance is affected by the following factors:
- Contact area of the wheel: The contact area of the wheel rotates around its centre when the swivel castor turns. This causes friction. The resistance is dependent on the interaction between the surface and the wheel tread, in addition to the size of the contact area.
- Resistance of the swivel head: The structure and quality of the swivel head have an impact on its swivel resistance.
- Offset of the swivel castor: The swivel resistance of the swivel castor is influenced by the distance between the centre of the swivel head and the centre of the contact area.
Wear resistance
The higher the point score in this category, the greater the wear resistance of the wheel.
In addition to other factors, the wear resistance incorporates the resistance to abrasion of elastomers or thermoplastic elastomers in accordance with ISO 4649. The resistance of other tread materials to abrasion was tested in accordance with ISO 4649.
Tread materials are assigned to different abrasion resistance categories in the graphic to the right.
| Material | Wear resistance | ||
| Pneumatic tyre / soft rubber | |
satisfactory | |
| Elastic solid rubber | |
good | |
| Super-elastic solid rubber | |
good | |
| Standard solid rubber | |
adequate | |
| Thermoplastic polyurethane (TPU), soft | |
good | |
| Thermoplastic rubber-elastomer (TPE) | |
satisfactory | |
| Polyurethane 75 Shore A | |
very good | |
| Polyurethane 92 Shore A | |
excellent | |
| Thermoplastic polyurethane (TPU), hard | |
very good | |
| Polypropylene | |
satisfactory | |
| Nylon | |
good | |
| Cast nylon | |
very good | |
| Cast iron / steel | |
excellent |