Options
Truck locks. Directional locks. Bumpers.
The functionality of wheels or castors can be enhanced by using different options. Blickle provides the following options: Jacks/truck locks, directional locks, bumpers, hub caps and STARLOCK® caps, swivel heads, axle tubes and adapter plates.
-
Truck locks / jacks
The truck locks and jacks are zinc-plated, blue-passivated and Cr6-free. They are attached directly to the transport unit. Truck locks are used to lock transport units in a resting position. By operating the pedal, the transport unit is somewhat relieved of its load without being lifted.
Jacks are used to raise a transport unit to take the load off the wheels while it is in a resting position. The jacks provide their best performance if the total height of the operated jack is 5 mm higher than the selected swivel or fixed castors.
Depending on the weight of the person operating the transport equipment, the lifting force is between 150 kg and 250 kg. The vertical load on the jack must not exceed 500 kg when raised.For more information click here.
Total height
[mm]Total height
actuated
[mm]Plate
dimensions
[mm]Bolt hole
spacing
[mm]Bolt
hole Ø
[mm]FF 100-1 108 138 100 x 85 80 x 60 9 To the product FF 125-1 133 163 100 x 85 80 x 60 9 To the product FF 125 142 180 140 x 110 105 x 75–80 12.3 To the product FF 150 170 208 140 x 110 105 x 75–80 12.3 To the product FF 160 175 213 140 x 110 105 x 75–80 12.3 To the product FF 200 217 255 140 x 110 105 x 75–80 12.3 To the product WH 160 166 209 140 x 110 105 x 75–80 12.3 To the product WH 200 207 250 140 x 110 105 x 75–80 12.3 To the product WH 250 257 300 140 x 110 105 x 75–80 12.3 To the product -
Directional locks
Directional locks fix the swivel motion of a swivel castor in specific directions. When the directional lock is activated, the swivel castor acts like a fixed castor without having to make structural changes to the swivel castor. Directional locks can also be retrofitted to castors. Directional locks are made from blue-passivated and zinc-plated steel or corrosion resistant steel
You can find more information here.
Bolt hole
spacing
[mm]Bolt
hole Ø
[mm]Total width
[mm]Actuation
lever
protrusion [mm]RI-04.03 75-80 11 110 94 To the product RI-04.01 60 9 85 107 To the product RI-05.01 60 9 85 107 To the product RI-03.01 60 9 84 75 To the product RI-05.03 75-80 11 110 111 To the product RI-03.01-KX 60 9 85 75 To the product RI-03.03-KX 75-80 11 110 97 To the product RI-03.03 75-80 11 110 94 To the product RI-05.03-KX 75-80 11 110 113.5 To the product -
Bumpers
Bumpers reduce the risk of damage to walls and transport trolleys in the event of a collision.
Bumpers are available for round and square tubes. Two different designs are available: a soft polyethylene with a hardness of 48° Shore D and solid rubber with a hardness of 75° Shore A. The wheels are non-marking and available in grey, grey white or silver grey. They are fastened or mounted to tubular frames in the outsides of vehicles.
Wheel Ø
[mm]Wheel
width
[mm]Hole
[mm]Hardness ARG 75/R10 75 23 10 75 Shore A To the product AW 100/V25 100 17.5 25 48 Shore D To the product AW 100/R25 100 17.5 25 48 Shore D To the product AG 100/V25 100 17.5 25 48 Shore D To the product AG 100/R25 100 17.5 25 48 Shore D To the product ARG 100/R26 100 23 26 75 Shore A To the product ARG 100/R32 100 23 32 75 Shore A To the product AW 125/V25 125 17.5 25 48 Shore D To the product AW 125/R25 125 17.5 25 48 Shore D To the product AG 125/V25 125 17.5 25 48 Shore D To the product AG 125/R25 125 17.5 25 48 Shore D To the product ARG 125/R32 125 23 32 75 Shore A To the product ARG 125/R26 125 23 26 75 Shore A To the product -
Hub caps and STARLOCK caps
Hub caps are made from zinc-plated, blue-passivated, Cr6-free pressed steel.
They protect the outside ball bearing of end wheels against dirt, dust, etc., and cover the axle end and wheel fitting. In end wheels, the ball bearing is slightly recessed on the outside of the hub. This makes it easy to fit the hub cap on the wheel hub.
STARLOCK® caps are an easy way to fix light duty wheels on an axle. The wheel is placed on an axle as the end wheel, and the STARLOCK® cap is pressed onto the outer end of the axle.
Total height
[mm]Shaft Ø
[mm]Outer Ø
[mm]ST-KA 12 7.5 12 26 To the product ST-KA 15 9 15 29.4 To the product ST-KA 20 11.7 20 38.2 To the product ST-KA 25 12.5 25 43 To the product -
Swivel heads
Swivel heads can be used for a wide variety of applications: Rotating plates, rotating platforms, flatbed turntables or axle-pivot steering systems. Combined with standard fixed castors, they can create castor systems without an offset, which are easy to steer.
Plate
dimensions
[mm]Bolt hole
spacing
[mm]Bolt
hole Ø
[mm]Load capacity
(static)
[kg]Flange plate
height
[mm]Flange plate internal
clearance
[mm]DK-L-3 140 x 110 105 x 75–80 11 400 28 20 To the product DK-LUH-3 140 x 110 105 x 75–80 11 1,000 31 21 To the product DK-LS-3 140 x 110 105 x 75–80 11 1,500 37 21 To the product DK-LS-35 175 x 140 140 x 105 14 2,500 44 24 To the product DK-LS-36 200 x 160 160 x 120 14 2,500 44 24 To the product DK-LS-38 255 x 200 210 x 160 18 5,500 60 25 To the product -
Axle tubes
The PTFE-coated stainless steel axle tube consists of a corrosion-resistant axle tube with a PTFE coating. When rotating and under load, the PTFE coating expands onto the inside of the plain bore of the wheel. This provides the desired pairing (PTFE / stainless steel) with outstanding sliding characteristics. It also reduces noise emissions. This option is available for a wide range of heat-resistant wheel series.
Total
length
[mm]Outer Ø
[mm]Internal Ø
[mm]XAT 12x37 37 12 8.2 To the product XAT 12x40 40 12 8.2 To the product XAT 12x47 47 12 8.2 To the product -
Adapter plates
Adapter plates can be used to compensate for differences between the mounting height of different castors. Adapter plates can also be used to modify the mounting height of the transport unit. Adapter plates are available in steel (zinc-plated, blue-passivated, Cr6-free) and synthetic (nylon, black) designs.
Plate
dimensions
[mm]Bolt hole
spacing
[mm]Bolt
hole Ø
[mm]Plate
thickness
[mm]AP1-10 100 x 85 80 x 60 9 10 To the product AP3-17 140 x 110 105 x 75–80 11 17 To the product APS1-02,5 100 x 85 80 x 60 9 2.5 To the product APS1-08 100 x 85 80 x 60 9 8 To the product APS3-04 140 x 110 105 x 75–80 11 4 To the product APS3-08 140 x 110 105 x 75–80 11 8 To the product APS3-10 140 x 110 105 x 75–80 11 10 To the product